Loading...

Strobe Light or Siren

   Tone Alert      Strobe Alert        
                        

   Tone Alert Accessory

Our Low Cost Tone Alert Accessory outputs a Speaker Alert Tone as soon as it detects the Relay Closure output from one of the applicable Natcomm Products to which it is connected.

Tone Alert uses an Internal Microprocessor circuit and Speaker to produce an Alert Tone or Alarm Tone, rather than the annoying very high frequency of inexpensive ‘Piezo Alarms’. 

It is used as a 'Plug In' accessory for our Ring Indicator, Off Hook Indicator, Telephone Line Monitor and other Natcomm Telephone Line Switches.

Tone Alert is NOT a Loud Ringer itself. There are many of those readily available.

It is designed to be used as a convenient Wall Mount or Desk Mount unit to directly 'Alert' local users of Incoming Calls or other Telephone Line conditions. 

It has a volume control pot located on the underside of the unit to alllow its Warning Tone output to be adjusted to suit.

It also has an Amplified 3.5mm Output, so that it can be used to output volume to suit any application :

  • A volume pot is located on the underside of the unit, to allow for volume adjustment to suit open office areas up to 200 sq m, or small factory areas.
     
  • An amplified 3.5mm Audio Output (7W) is also provided to allow for connection of additional standard 8 Ohm Speakers or PC type Speakers with Amplifier and Volume Control. This will suit larger Office Environments, Noisy Office Environments, or small-medium sized Factory Areas. 
     
  • The 3.5mm Audio Output can also be connected to an External Amplifier so that it’s Alarm Tone can be used for ANY sized Office Environment, External Area or Factory Area serviced by a suitable Amplifier. 

 

DIP SWITCH FACILTY
 

Tone Alert is fitted with a Dip Switch located on the underside of the unit, to allow you to

1) Choose 1 of 4 different Tone ON/OFF Cadences, to suit different applications (see below).

  • A Continuous Tone

  • A repeating Tone that is 4 Seconds On and then 4 Seconds Off

  • A repeating Tone that is 8 Seconds On and then 8 Seconds Off

  • A repeating Tone that is 2 Seconds On and then 4 Seconds Off (same as a Phone Ring)

 

2)  This option will also allow you to change the frequency of the Tones that are by a Dip Switch on the underside of the unit. 

  • 400Hz Alert Tone (same frequency as a Telephone Ring which can be associated with an Alert condition)
     
  • 1200Hz Alarm Tone (a higher pitched tone that can be associated with an Alarm condition)

 

 

The above example shows the Accessory connected to our Ring Indicator. You can substitute the Ring Indicator switch for our Off Hook Indicator or Telephone Line Monitor, Telephone Line Switches. 

The Accessory is powered direct from the Natcomm Telephone Line switch that it is connected to. It connects with a 4 wire telephone cable. a 3ft cable is supplied, together with an easy mount plastic molded Wall Mount Bracket for the accessory. The accessory can be mounted up to 100ft away from the Natcomm Switch id solid core telephone cable is used (Cat3 or Cat5 is ideal). If the accessory needs to be located nore than 100ft away, a local 12V power adaptor (not supplied but optionally available) can be be used to power the accessory via its power input.
 

Strobe Alert Accessory

Our Low Cost Strobe Alert Accessory uses EIGHT High Intensity RED LED’s which Flash to alert Users as soon as it detects a Relay Closure Output from the applicable Natcomm Product that it is connected to. When Wall Mounted, it is Ideal for a small office (up to 500-1000 sq ft), or for small Factory Areas.

For Larger areas, Two or More Strobe Alert Accessories can be connected in parallel to the Natcomm unit :

 

DIP SWITCH OPTION

A Dip Switch is Optionally available on Strobe Alert.

It consists of a Dip Switch located on the underside of the unit, to allow you to choose 1 of 4 different Strobe Flash Cadences (times that the LED's are ON and OFF) to be changed to suit different applications.

With this option STROBE ALERT can output :

  • A Continuous Strobe Flash

  • Strobe Flash that is 4 Seconds On and then 4 Seconds Off

  • Strobe Flash that is 8 Seconds On and then 8 Seconds Of

  • Strobe Flash that is 2 Seconds On and then 4 Seconds Off (sames as a Phone Ring)

The cost of this option is $10.00

 

 

The above example shows the Strobe Accessory connected to our Ring Indicator. You can substitute the Ring Indicator switch for our Off Hook Indicator or Telephone Line Monitor Telephone Line Switches. 

 

Power and Connection

Both Accessories are powered direct from the Natcomm Product and connect with just 4 wires. A 3m cable is provided with each Accessory. 

If the Accessory needs to be remote from the Natcomm unit, it can be located up to 100 metres away if solid core cabling is used. Cat 3 (standard telephone cable) or Cat5 cable or Standard Telephone Cable is ideal. 

If the Accessory is to be located more than 100 metres away, it has a standard 12VDC (2.5mm) Power Input Socket to allow for local powering. You can use a 12VAC or 12VDC input of any polarity.

Using Both Accessories

Our Tone Alert and Strobe Alert accessories can be used at the same time with any of the Natcomm Products that they are designed to work with. In this situation, a special 4P4C Double Adaptor is supplied at no additional charge.

The Adaptor has a single plug which fits into the Output of the Natcomm Telephone Line switch. The Adaptort also has 2 sockets to which both of the supplied 'Curly Cord' fits into.  

Use With Non Natcomm Products

Both Accessories can be used with NON Natcomm Products that provide a Dry Relay contact output.

As The Accessory is normally powered from the Natcomm Telephone Line Switch, it will be necessary to power Tone Alert via the (2.5mm) Power Input Socket. You can use a 12VAC or 12VDC input of any polarity. A min of 300mA should be provided to ensure correct operation. A suitable Power Adaptor ($15.00) is available by calling our factory on ph (07) 5596 5128.  

 

Optional Wall Mounting Bracket

       

 

The plastic enclosure of Both accessories has 2 ‘Key Hole Slots’ molded into the bottom plate to provide for Easy Wall Mounting.

A Wall Mount Bracket with 2 small screws can be supplied at an additional cost of $5.00.

This Accessory Bracket screws direct onto a wall with the 2 small supplied screws. Once the Wall Mount Bracket is in place, the Accessory 'Clips' straight into the Keyholes and then you just pull it down lightly to lock it into place.

TONE ALERT 

STROBE ALERT 

 

 
Off Hook Indicator - with Programmable Del...

AU $229.00

Programmable Delay  Model (OHI-2) is fitted with the Delay Option  : This model is fitted with a set of 4 Dip Switches located on the underside of the unit which will allow you to set a DELAY TIME before Off Hook Indicator closes its internal relay to Alert the attached Tone Alert or Strobe Alert accessory. The choice of Delay Times are : 1, 2, 5, 10, 15, 30 or 60 mins and 1, 2, 3, 4, 5, 6 and 7 hrs.

   
Strobe Alert Accessory

AU $69.00

Strobe Light Accessory uses EIGHT High Intensity RED LED’s which Flash to alert Users as soon as it detects a Relay Closure Output from the applicable Natcomm Product that it is connected to. When Wall Mounted, it is Ideal for a small office (up to 500-1000 sq ft), or for small Factory Areas.
For Larger areas, Two or More Strobe Light Accessories can be connected in parallel to the Natcomm unit.